Welcome to Dongguan Mingke Technology Co.,LTD !

Service：400-800-3359

新阳不锈钢
导航
mechanical equipment

News

资讯分类
07-14

Dongguan Mingke Technology Co.,Ltd

Dongguan Mingke Technology Co.,Ltd
Dongguan Mingke Technology Co.,Ltd
07-06

MK-2030 small screen printing machine goes on sale

Dongguan Mingke Technology Co.,Ltd is a grand launch a strong competitive advantage in cost-effective for small screen printing machine. This section screen printing machine maximum printing area can reach 200 * 300mm, a small countertop design, microcomputer control each function with high degree of automation, simple operation, stable performance, run fast, smooth operation. Up to 1200 times per hour, printing clear, beautiful. Machine Photo Gallery:
MK-2030 small screen printing machine goes on sale
05-21

Maintenance of screen printing machine

 In our many years of practical experience, usually falling into disrepair due to leaving the damaged parts of the case are numerous, so here we provide some maintenance work and precautions, the operator can really do hope that millions of parts in order to avoid the wear and failure, resulting in time and human and financial resources on unnecessary waste, and general maintenance work include: a pneumatic parts and maintenance, two, parts and components used to care. Maintenance Special offers three items, as follows: A compressed air transportation and maintenance: 1 should prevent leakage of compressed air transportation in order to save electricity costs, machine uses air pressure to be maintained at 6 kg in order to maintain the stable operation of the machine, its pressure source should be 7-8 kg. Therefore, the bottom line starts at the set air compressor pressure point must be 7 kg or more. 2 air conditioning: screen printing machine pneumatic components due to move, thus affecting air pressure system for large components, compressed air containing impurities to know: dirt, rust, dust, etc. These will be debris in the pneumatic components accelerated component wear, affect the performance and shorten the service life, it is in the machine pressure piping design, the compressed air into the machine in front of the stage to install a set of air conditioning group (commonly known as FRL) to protect the machine inside the pneumatic system the various components. In this remind users to pay attention to the water storage capacity of not more than glass cup of l / 2, the machine FR.L automatic drainage patterns, once no ventilation, it will automatically drain, but a long run to the attention of artificial drainage, or loose about pressure, it automatically drain to prevent water from entering surface pressure systems affect the service life of pneumatic components. FR.L is equipped with oil cup, a lubricant, the user should always check the oil cup, oil is insufficient time to add to, but not exceeding the oil cup 2/3 of the oil supply amount adjustment generally adjusted to each min 1 drop is appropriate. Second, parts of the care and maintenance Work site selection: Stay away from dust and large temperature higher place in order to maintain the stability of the printing quality and the surrounding software life to save costs. Mechanical maintenance: 1 machine should be kept clean after the daily hard work do not forget to wipe clean the machine, and the screen clean inside the ink, so as to avoid causing clogging ink hardening phenomenon. 2 sliding parts maintenance: In order to ensure stable operation of the machine, we must be prepared to this maintenance, the sliding part should be timed to add oil to ensure lubrication and remove grease and dirt in order to avoid sliding contact portion accelerated wear parts. 3 parts Maintenance: Due to the use of more sophisticated machine sliding rails, so should be used away from dusty places, adjust the machine to note is that when we can not use a hard object struck linear guide parts at the seal, Otherwise, if the result of percussion and deformation, can not get the job done more harm than good, but also pay attention to timely clean the sliding part, to avoid falling into the ink and other foreign matter and affect the composition and separation and adjustments. Third, the maintenance methods l. Pneumatic components: ① Do not allow excess moisture and debris from entering the air pressure within the system in order to avoid failure and life less alkaline. ② Keep the compressed air to dry and clean. ③ daily water within the air compressor bleed more than once. 2 FRL: ① the use of pressure to maintain six kilograms. ② daily discharge treatment forest more than once. ③ Check whether the amount of oil filled 2/3. ④ Push the valve manually when not in a long time, should be put in the rear push off. 3. Lubrication: A class of fats: for use in Air conditioning group. ① cycle oil R32 # (pressure, conditioning group for oil) ② oil for use in uranium rail line order / linear rail lubrication. Class B Grease: a lubricant for the bushing and the optical axis Level NLGI2, low viscosity butter (butter) (4) Other: ① stops working, turn off the power and compressed air source, avoiding danger. ② Department of Precision control valve assembly, to avoid collision.
Maintenance of screen printing machine
05-21

The new year's speech

    Golden Tiger shouts the old year, LUCKY Rabbit New Year. Filled with the joy of harvest, we bid farewell to a brilliant 2010, ushered in a brand new 2011.       Here, Dongguan Machinery Manufacturing Co. Juquanwan staff, has been the concern and support to the development of Dongguan Juquanwan all walks of life, to new and existing customers and partners to extend my heartfelt thanks and best wishes, I wish you good health, well, good luck, fun!
The new year's speech
05-21

Recruitment national distributor

       Dongguan Mingke Machinery Manufacturing Co., Ltd. is a screen printing machine, small screen printing machine, printing machine, screen printing supplies and other products specialized in developing, manufacturing and sales of businesses, the company set up technology development department, production department, sales department.       Company is located in Dalang Town, Dongguan City Jin Langnan Road, No. 483-487. The company has a complete and scientific quality management system. Always adhering to customer-oriented business philosophy. Products widely used in a variety of materials in the printing process. The company's integrity, strength and quality of products recognized by the industry.       For business development, the National Recruitment regional distributors, welcome friends to visit Dongguan Mingke Machinery Manufacturing Co., Ltd. visit, guidance and business negotiation.
Recruitment national distributor
previous page
1
底部logo

  After years of endeavor, Mingke printing machine has a good reputation for steady function, fast speed and high quality, and also wins favors by customers both home and abroad.

这是描述信息
这是描述信息

Service support

 

 

Message Board

留言应用名称：
Messages
描述：
验证码